Battlegown, April-June 2013

I haven’t been posting updates on my latest project to the Shindig Facebook Page because it is supposed to be a surprise gift from one of my friends (J) to his best friend (N). N knows something’s going on, because I had to take her measurements (and encase her in duct tape – read on). But no fittings part way through! No double checking with the client about details! No help interpreting the image! It is a really fun project, and since no one has seen it at any stage, I figured I’d blog about it’s creation!

The project: BATTLEGOWN!

The Inspiration: This photo below. Unknown source unfortunately! Very awesome artwork, if anyone knows who I should credit please tell me.

Battlegown

Step 1: Sketches. Many many sketches. Even though I have the image in front of me, it helps to sketch out the garment pieces. It’s an exercise. When I sketch what I see, I have to pay attention to every aspect of it. I have to think through where I will put the fasteners and what that shadow means in fabric. Is that pouffy skirt gathered? Is there a petticoat underneath? And so on…

2013-03-20_22-55-00_677

Step 2: Measurements…and duct tape. This was my first attempt to use leather, other than a calfskin vest I made for the TV pilot “Turn”. I’ve never made armor or stretched leather, so I’m really excited to try it! I did a lot of research. I tried to find a book to help, but apparently there is no published instructional book (that I could find) on leather armor. The most helpful tutorial I found is from Ember Costumes. Thanks Ember!

What all the sources were telling me is that I’d need a custom form on which to stretch the chest piece. I got N to put on one of my t-shirts (an Outback Steakhouse t-shirt that was cathartic to destroy – those of you who know me will understand). I grabbed a roll of duct tape and rolled it around N. Then I cut a slit up the back through the duct tape and t-shirt. N was a very good sport, especially considering she didn’t know why I was doing this! I taped up the now-empty t-shirt in the back and stuffed it with poly-fill.

Duct Tape Form 1

Duct Tape Form 2

I used 4-inch wide strips of plaster fabric (bought on Amazon) to make the mold stronger. I did four layers of the plaster strips, letting each layer dry before adding the next. And voila! N’s torso mold is complete!

Plaster Form

Step 3: Shopping! This can happen at various points in my process. Sometimes I like to buy the fabric right away and keep it in mind while I’m draping. Other times I have no idea how much I’ll need, so I have to wait until I make the pattern. In this case, I got excited and bought everything right away.

Fabric!

Step 4: Draping. I make my patterns on an adjustable dress form.

2013-05-02_19-18-25_809

Step 5: Cutting and Sewing. The base dress was pretty straight forward. I decided it would look nice to have a lace-up front, so I put in about 100 eyelets.

Lace-up Front

The most challenging part was the blue fleur de lis appliqué. I had to make the appliqué myself. I made a template and traced it onto some Wonder Under. Wonder Under is a fabulous product that you can buy at Jo-Ann Fabrics. It is basically paper with little dots of glue on one side. I cut out the shape I needed and pressed it glue-face-down onto the satin.

Applique 1

Then I cut that out, peeled off the paper (the glue sticks to the fabric and not the paper), and pressed it onto the skirt. Finally, I ran a tight zig-zag stitch around each piece to prevent fraying.

2013-05-29_21-11-50_15

I made up some 2-inch bias tape of the same fabric for the trim.

2013-05-29_23-08-42_371

2013-05-29_23-52-20_378

Step 6: Tabard. I bought some beautiful, but horrendously expensive upholstery fabric for the tabard. The colours and motifs were just so perfect that I couldn’t resist. Luckily, the fabric was so wide that I only had to buy a quarter yard, and I used a coupon (yay coupons!). I cut the fabric to width, added the neck hole, and joined the shoulder seams.

2013-05-29_23-53-47_224

2013-05-29_23-54-09_338

2013-05-29_23-54-45_193

Then I finished all the edges off with some store-bought bias tape. Sometimes it just does the trick!

2013-05-29_21-12-39_210

Step 7: Leather. Even though the first thing I did was make a mold for the armor, I got scared and didn’t want to cut the leather. When I finished the dress, I was forced to start the armor. Courage! I bought leather from the Online Fabric Store’s closeout leather section. I cut a 26 x 26 inch rectangle of leather, which was about the dimension of the mold. Then I filled a pot with hot tap water and soaked the leather.

2013-05-31_13-51-35_553

I put my plaster mold into a plastic bag so the plaster wouldn’t get on the wet leather.

2013-05-31_13-50-54_771

Using some clamps, I stretched and smoothed the leather on the mold.

2013-05-31_14-09-11_3

2013-05-31_14-09-38_609

Once it dried, I removed the clamps and put the leather back on the dress form.

2013-06-02_11-31-23_869

I trimmed the leather to the correct shape. I used a rectangular piece for the back and a semi-circle for the neck strap. These lace up with more eyelets. Next it was time to paint the leather! I used acrylic leather paint. I first washed the chest piece with a mixture of water and a very small amount of paint, using a sponge. This makes the next layer stick to the leather better, and is not noticeable afterwards. The crest I designed was inspired by both the original artwork and the tabard fabric, and the icon is special to N.

2013-06-03_18-52-24_422

Time to make the gorget! I made a pattern by cutting out a circle in paper, cutting out a neck hole, and cutting a radial line. Then I put this on the dress form and adjusted it until it sat right. Then I cut the pattern into three equal parts and added some “seam allowance” for the overlap.

2013-06-02_16-39-23_8

I taped the pieces in place on the back, since you can’t really pin leather. Then I hand basted the back seams together with a whip stitch. If you attempt this, make sure you use a thimble, because hand-stitching leather can really tear up your fingers.

2013-06-02_16-38-53_820

And for the final step, I added eyelets for the lacing.

2013-06-02_17-31-18_375

And project complete!!! Here’s some more pictures. I’ll post pictures of N wearing it when I get them!

2013-06-03_18-53-17_585

2013-06-03_18-53-05_831

Zia Cosplay, March 2013

This is a bit late, and most of you have seen pictures on my Facebook page, but here’s a breakdown on the Zia costume I made this year if anyone’s interested.

FacebookPic

The pants were fairly straight-forward, so I started with them. The’re pretty standard bloomers, on steroids. I worked from a bloomers pattern and made them much wider, and then added layers.

2013-02-20_17-41-38_826

First I made some bias tape to make the pink stripes, which I top-stitched on (so booooooring and a long process).

2013-03-23_17-14-40_846

The outer layer is stretch poplin, which has quite a bit of body. I put in a layer of tulle and then some cotton broad cloth for lining so they’d be comfy.

2013-03-23_15-54-47_490

2013-03-23_22-19-55_590

The jacket was much more involved! I didn’t have a pattern that looked remotely like it, so I draped it from scratch. I didn’t have a dress form Caitie’s size (she is a tiny person!) so I ordered a new size Small adjustable dress form. Introducing Catalina! She’s a Dritz Sew You, and I’m very happy with her. She’s light-weight, of course, and made of cheap plastic. But I haven’t had any issues with adjusting her, and I really appreciate the front dials for quicker adjustments (Matilda, my size Medium Dritz My Double Deluxe doesn’t have that).

857425_541827002516013_1451608326_o

I adjusted Catalina to Caitie;s measurements, and came up with a pattern pretty quickly.

2013-02-26_20-42-01_231 2013-02-26_20-42-58_698

The major challenge was the collar! I think Zia’s voluminous collar is pleated. SO I made the shape of the collar without the pleats to get the general shape right:

2013-02-26_21-05-37_7982013-02-26_21-05-06_750

I added the pleats by cutting the collar into 1-1/4 inch strips and then with paper adding in 2 inches between the strips. Getting the pleats to match up and go in a direction that would maintain the shape of the collar was a nightmare. It took about 6 hours, but I did it!

2013-03-01_00-23-40_9502013-03-01_00-24-11_950

Face fabric time! I used a poly-cotton gabardine for the main fabric, which is soft and has a nice drape for a jacket. Then some shiny copper costume satin for the accent backed with stiff interfacing. I acquired four delicious brass buttons at Fabric.com and six PERFECT tassels thanks to the Tassel Outlet on Etsy. I lined the jacket in copper cotton broadcloth. For the collar, I used a double layer of warm and comfy wool blend coating. Since the coating is so lush, it tended to droop in the front. I fixed that problem with two small pieces of corset boning.

2013-04-02_12-44-19_672 2013-04-02_12-44-36_297 2013-04-02_12-44-55_272 2013-04-02_12-45-07_657 2013-04-02_12-45-37_306 2013-04-02_12-45-46_299

 

Zia made her first con appearance at Anime Central! More pictures to come, whenever Caitie gets them to me – hint hint!!

AnimeCentral

“Murloc Aggro.” Designed and built by Tania Bukach, 2011

“Cerim.” Built and acted by Tania Bukach, 2006